Zebra XiIIIPlus Manuale Utente Pagina 129
- Pagina / 152
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Troubleshooting
Print Quality Problems
23063L-001 Rev. 2 6/21/2004 RXiIIIPlus User Guide 105
Light, consistent
vertical lines running
through the labels
The printhead or platen roller is
dirty.
Clean the printhead and platen roller as instructed in
Printhead and Platen Roller on page 91.
Caution • The printhead is hot and can
cause severe burns. Allow the printhead
to cool.
Electrostatic Discharge Caution •
Observe proper electrostatic safety
precautions when handling any static-
sensitive components such as circuit
boards and printheads.
Intermittent creases
on the left and right
edges of the labels
There is too much toggle
pressure on the printhead.
Reduce the toggle pressure. See Adjust Printhead
Pressure and Toggle Position on page 38.
Electrostatic Discharge Caution •
Observe proper electrostatic safety
precautions when handling any static-
sensitive components such as circuit
boards and printheads.
Wrinkled Ribbon The ribbon is not loaded
correctly.
Load the ribbon correctly. See Load Ribbon
on page 26
.
The darkness setting is incorrect. Set the darkness to the lowest possible setting for
good print quality. See Adjusting Print Darkness
on page 44.
Incorrect printhead pressure or
balance.
Set the pressure to the minimum required for good
print quality. See Adjust Printhead Pressure and
Toggle Position on page 38.
Electrostatic Discharge Caution •
Observe proper electrostatic safety
precautions when handling any static-
sensitive components such as circuit
boards and printheads.
The labels are not feeding
correctly. They are shifting from
side to side.
Make sure that the media guide and media supply
guide touch the edge of the media.
Adjust the ribbon strip plate.
Table 12 • Print Quality Problems (Continued)
Problem Possible Cause Recommended Solution
- User Guide 1
- Contents 5
- Proprietary Statement 9
- Liability Disclaimer 10
- Limitation of Liability 10
- Warranty Information 11
- Related Hardware Items 12
- Repair Services 13
- Printer Software 15
- License Agreement 15
- 3. RESTRICTIONS 16
- Contacts 22
- Document Conventions 23
- Related Documents 24
- Introduction 25
- Exterior View 26
- Front Panel 27
- Front Panel Buttons 28
- Front Panel Lights 29
- Printer Components 30
- Printer Setup 31
- Before You Begin 32
- Report Shipping Damage 33
- Store or Reship the Printer 33
- Select a Site for the Printer 34
- Power Cord Specifications 35
- Data Cable Requirements 37
- Types of Media 38
- Non-Continuous Media 39
- Continuous Media 39
- (label profile) 40
- When to Use Ribbon 41
- Ribbon Width 41
- Coated Side of Ribbon 41
- Adhesive Test 42
- Ribbon Scratch Test 42
- If the ribbon... Then 43
- Printer Operation 45
- Load the Printer 46
- Load Fanfold Media 48
- Load Ribbon 50
- 8. Close the printhead 53
- Remove Used Ribbon 54
- PRINTER 55
- PRINTER READY 55
- Calibrate the Printer 57
- Adjust and Calibrate Sensors 58
- 11. Close the printhead 59
- Transmissive (Media) Sensors 60
- Toggle Position Adjustment 62
- Printhead Pressure Adjustment 62
- 6. Tighten the locking nuts 63
- Front Panel Controls 65
- Overview 66
- Password-Protected Parameters 67
- Front Panel LCD 68
- PRINT MODE 69
- MEDIA TYPE 69
- SENSOR TYPE 69
- PRINT METHOD 69
- PRINT WIDTH 70
- MAXIMUM 70
- Parameter Action/Explanation 71
- 1. When the LCD displays 72
- 2. Do you wish to continue? 72
- DELIMITER 77
- ZPL MODE 77
- LABEL TOP 79
- POSITION 79
- VERIFIER 79
- ZebraNet 83
- RFID Guidelines 85
- Transponder Placement 86
- ZPL II Commands for RFID 87
- Host Verification 88
- RFID Setup 89
- ^RS,800,,2,P^FS 90
- ^RS,800,500,2,P^FS 91
- Read Tag 92
- Write Tag 93
- Sample of RFID Programming 94
- Parallel Port 98
- 36-Pin Connectors Description 99
- Serial Port 100
- Serial Pin Configuration 101
- RS-232 Interface Connections 102
- DB-9 to DB-25 Connections 103
- Modem Connection 103
- Data Ports 104
- USB 2.0 Port 105
- Memory Cards 107
- PCMCIA Memory Card 108
- CompactFlash Card 110
- 1. Turn the AC power Off (O) 110
- Routine Maintenance 113
- Cleaning Schedule 114
- Clean Exterior 114
- CLEAN HEAD NOW 114
- Clean Interior 115
- 1. Open the printhead 115
- 7. Close the printhead 116
- Snap Plate 119
- Replace Fuse 120
- Troubleshooting 123
- LCD Error Messages 125
- RIBBON IN 126
- HEAD TOO HOT 126
- HEAD COLD 127
- OUT OF MEMORY 127
- Print Quality Problems 128
- Communications Problems 130
- Printer Diagnostics 132
- 1. Turn Off (O) the printer 133
- Specifications 137
- Features 138
- Bar Codes 139
- Compliance for All Printers 139
- General Specifications 140
- Print Specifications by Model 141
- Ribbon Specifications 142
- Label Specifications 143
- CHECK RIBBON 145
- HEAD ELEMENT BAD 146
- HEAD OPEN 146
- PAPER OUT 148
- Ribbon Out 149
- Customer Order # 23063L-001 152
- © 2004 ZIH Corp 152
Prodotti e manuali riguardandi Stampanti per etichette Zebra XiIIIPlus
Stampanti per etichette Zebra ZT210 Manuale Utente
(168 pagine)
(168 pagine)
Stampanti per etichette Zebra Z4Mplus Manuale Utente
(178 pagine)
(178 pagine)
Stampanti per etichette Zebra QL+ Manuale Utente
(86 pagine)
(86 pagine)
Stampanti per etichette Zebra Z4M Manuale Utente
(102 pagine)
(102 pagine)
Stampanti per etichette Zebra Z4M Manuale Utente
(57 pagine)
(57 pagine)
Stampanti per etichette Zebra 105SL Manuale Utente
(130 pagine)
(130 pagine)
Philips SHD9200/10 manuali
Manuali dei proprietari e guide per l'utente per Cuffie Philips SHD9200/10.
We fornisce 1 manuali pdf Philips SHD9200/10 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale