Zebra ZT420 Guida Utente Scaricare il pdf (Pagina 43)

Printer Setup and Operation

Load the Media—Peel-Off Mode (with our without Liner Take-Up)

4/8/14 ZT400 Series™ User Guide P1066582-002

2. Extend the media approximately 18 in. (500 mm) out of the printer.

3. Remove the exposed labels so that only the liner remains.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 191 192

ZT400 Series™ 1
User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
About This Document 9
Who Should Use This Document 10
Introduction 11
Printer Options 12
Printer Components 13
Control Panel 14
Zebra printer 15
Types of Media 16
Printer Setup and Operation 17
Ribbon Overview 18
Adhesive Test 19
Ribbon Scratch Test 19
Printer Setup and 21
Operation 21
Handling the Printer 22
I) may damage the 24
Data Cables 26
115 V AC 27
230 V AC 27
Power Cord Specifications 28
Select a Print Mode 30
Rewind mode 33
Load the Media 34
Roll Media 35
Fanfold Media 35
Rear Feed 36
Bottom Feed 36
Roll Media (Continued) 37
(Continued) 37
If using… Then… 39
Final Steps for Tear-Off Mode 40
4. Close the media door 41
Rewind Option 46
Liner Take-Up Option 46
Final Steps for Rewind Mode 51
Load the Media—Rewind Mode 52
Final Steps for Cutter Mode 57
5. Close the media door 59
Load the Ribbon 60
Printer Setup 61
If... Then 63
PAUSE to enable printing 63
Printer Configuration 65
Adjust Printer Settings 66
Print Settings 67
• THERMAL TRANS 68
• DIRECT THERMAL 68
• TEAR OFF 69
• CUTTER 69
FEED + CANCEL during printer 71
~JD to enable, ~JE to disable 75
^JI, ~JI 76
Network Settings 77
RFID Settings 80
RFID ANTENNA 81
Language Settings 83
• ZPL II 85
Sensor Settings 86
Port Settings 87
• XON/XOFF 88
• RTS/CTS 88
• DSR/DTR 88
BlueTooth Settings 89
User Menus 90
HOME MENU 91
SETTINGS 91
▼ XXXXXXX ▲ 93
SETTINGS Menu 94
LEFTARROW 95
TOOLS Menu 97
NONE is listed 99
RIGHT SELECT to select STOP 99
User Menus—TOOLS Menu 100
Network Menu Shortcut 101
or RIGHT ARROW 101
NETWORK Menu 102
User Menus—NETWORK Menu 103
RFID Menu Shortcut 107
RFID Menu 108
User Menus—RFID Menu 109
OK or press 110
RIGHT SELECT to select GO 110
LEFTARROW or RIGHT ARROW 110
LANGUAGE Menu 111
SENSORS Menu 113
TAKE LABEL 114
PORTS MENU 114
PORTS Menu 115
ZEBRA TECHNOLOGIES 116
BLUETOOTH MENU 116
BLUETOOTH Menu 117
LOAD BACKING 119
REMOVE RIBBON 119
CALIBRATING 121
PLEASE WAIT 121
RELOAD ALL 122
CONTINUE 122
Reload the ribbon (if used) 123
Close the printhead 123
Close the media door 123
Adjust the Printhead Pressure 124
If the media... Then 125
Remove Used Ribbon 128
Routine Maintenance 129
Area Method Interval 130
Printer Exterior 131
Media Compartment and Sensors 131
Raise the media door 132
8. Close the media door 135
Clean the Peel Assembly 136
Clean the Cutter Module 140
Remove the cutter shield 141
Replacing Printer Components 144
Lubrication 144
Troubleshooting 145
Meaning of Indicator Lights 146
Printing Issues 148
Ribbon Problems 151
RFID Problems 152
MEDIA POWER UP and 153
O) and then back on (I) too 154
O) the printer 154
I) the printer 154
Error Messages 155
RIBBON OUT 156
PH NOT AUTHENTICATED 156
REPLACE PRINTHEAD 156
Display/ 158
Indicator Lights 158
Communications Problems 159
Miscellaneous Issues 160
Printer Diagnostics 162
CANCEL Self Test 163
PAUSE Self Test 164
FEED Self Test 165
Print Quality Description 166
FEED + PAUSE Self Test 168
CANCEL + PAUSE Self Test 168
FE indicates a framing error 169
PE indicates a parity error 169
NE indicates noise 169
Sensor Profile 170
Specifications 173
General Specifications 174
Printing Specifications 175
Media Specifications 176
Ribbon Specifications 177
Glossary 179
4/8/14 P1066582-002 183

Commenti su questo manuale

Nessun commento

Zebra ZT420 Guida Utente Pagina 43

Commenti su questo manuale

Prodotti e manuali riguardandi Stampanti per etichette Zebra ZT420