Zebra 160S Guida Utente Scaricare il pdf (Pagina 36)

Removing Used Ribbon (160S)

Refer to Figure 2.10.

1. Turn the knob at the end of the Ribbon Take-Up Spindle (1) clockwise

until it stops. This will cause the Ribbon Release Bars to pivot down

(2), easing the spindle’s “grip” on the wound ribbon.

2. Slide the ribbon off of the Ribbon Take-Up Spindle. Once the used rib-

bon has been removed, ensure that the arrow on the knob aligns with

the indented notch in the Ribbon Take-Up Spindle (see inset).

3. Remove the empty core from the Ribbon Supply Spindle.

4.Followtheribbonloadingprocedureonpage2-7toloadthenewrib-

bon.

Zebra S-Series User’s Guide 2-13

Figure 2.10 Removing Used Ribbon (160S)

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 105 106

User's Guide 1
Table of Contents 4
Introduction 10
Communication Capabilities 11
Print Mechanism Capabilities 11
Media and Ribbon Requirements 12
Warnings and Precautions 13
Repacking 14
Ribbons and Printhead Wear 14
Printer Specifications 15
Bar Codes 17
Standard Fonts 18
Font Matrix 19
Type* Character Size 19
Physical 21
Electrical 21
Communications Interface 22
Environmental Ranges 22
Options and Accessories 22
Installation 24
Power Connection 25
AC Power Fuse Replacement 26
115 VAC Operation 26
230 VAC Operation 26
Site Requirements 27
Ribbon Loading (105Se) 27
Figure 2.3 Making a Leader 28
Ribbon Loading (160S) 30
Media Loading 31
Tear-Off Mode 33
Rewind Mode 33
Peel-Off Mode 33
Cutter Mode 34
Fanfold Media 34
Removing Used Ribbon (105Se) 35
Removing Used Ribbon (160S) 36
Initial Printer Power Up 37
Operation 38
Media Transport Modes 39
Front Panel Keys 41
Front Panel Lights 42
Power On Self Test 44
Printer Self Tests 44
CANCEL Key Self Test 46
PAUSE Key Self Test 47
FEED Key Self Test 48
MODE Key Self Test 49
PAUSE Key and CANCEL Key Test 49
Extended Printer Diagnostics 50
Sample ZPL II Label Formats 51
Configuration and Calibration 54
Table 4.1 55
Table 4.2 56
Configuration Mode 57
Adjusting the Print Darkness 59
Interconnections 60
RS-232 Serial Data Port 61
RS-232 Cabling Requirements 62
Interconnect to DTE Devices 63
Interconnect to DCE Devices 63
Parallel Cabling Requirements 64
Parallel Interface 64
Signal Descriptions 65
Preventive Maintenance 66
Printhead and Platen Roller 67
Cutter Module 68
Lubrication 69
Adjustments 70
Troubleshooting 76
Peel-Off 82
Media Rewind 82
Fanfold Supply Bin 83
Optional Printer Fonts 84
230 VAC Factory Setup 84
(Not available for 105Se 85
300 dots/inch) 85
(105Se Only) 85
230 VAC Power Cord 86
Appendix B - ASCII Code Chart 88
Figure C.1 Bar Code Examples 92
S-300 printer 94
Glossary 98
Customer order #31460L 106
Manufacturer part #31460LB 106

Commenti su questo manuale

Nessun commento

Zebra 160S Guida Utente Pagina 36

Commenti su questo manuale

Prodotti e manuali riguardandi Stampa e scansione Zebra 160S