Zebra Z6Mplus Guida Utente Scaricare il pdf (Pagina 30)

12 Z4Mplus/Z6Mplus User Guide 13163L Rev. 3 5/20/2004

Printer Setup

Connect the Printer to a Power Source

• The AC power plug and IEC 320 connector must bear the certification mark of at least one

of the known international safety organizations shown in Figure 6.

Figure 6 • International Safety Organization Marks

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 141 142

User Guide 1
Proprietary Statement 7
Liability Disclaimer 8
Limitation of Liability 8
Declaration of Conformity 10
Warranty Information 11
Related Hardware Items 12
Supplies Products 12
Repair Services 13
Contents 15
Contacts 16
Document Conventions 17
Related Documents 18
Introduction 19
External View 20
Front Panel 21
LCD Display Settings 22
Print Modes 23
Printer Media Compartment 24
Printer Setup 25
Before You Begin 26
Report Damage 27
Select a Site for the Printer 28
Power Cord Specifications 29
Cable Requirements 32
Types of Media 33
Non-Continuous Media 34
Continuous Media 34
When to Use Ribbon 35
Ribbon Width 35
Coated Side of Ribbon 35
Adhesive Test 36
Ribbon Scratch Test 36
If the ribbon... Then 37
Printer Operation 39
Front Panel Keys 41
Front Panel Lights 42
Load Roll Media 43
Cutter Mode 44
PAUSE to enable printing 45
Peel-Off Mode 46
Liner Take-Up Mode 48
Liner Slide Tab 50
Liner Slide 50
Rewind/Peel-Off Mode 51
Liner Removal 52
Rewind Mode 53
Media Removal 54
Bottom Feed 56
Rear Feed 56
Load Fanfold Media 57
Load the Ribbon 58
Remove the Ribbon 59
Calibrate the Printer 60
Z6Mplus - 300dpi 61
Z4Mplus - 200dpi 61
Print a Configuration Label 62
If the label... Then 62
LIST NETWORK 63
Adjust Printhead Pressure 64
Install Memory Card 66
Configuration 67
PRINTER 68
Exit Configuration Mode 69
^KP (Define Password) 70
^KPx, where x can 70
Ø (zero) 70
ENTER PASSWORD 70
DARKNESS 71
PRINT SPEED 71
TEAR-OFF 71
TEAR OFF 71
PRINT MODE 72
MEDIA TYPE 72
PRINT METHOD 73
SENSOR TYPE 73
SENSOR SELECT 73
SAVE CHANGES PERMANENT 74
SAVING PERMANENT 74
PRINTER READY 74
PRINT WIDTH 77
Parameter Action/Explanation 78
PARALLEL COMM 82
SERIAL COMM 82
DATA BITS 82
HANDSHAKE 83
PROTOCOL 83
NETWORK ID 83
COMMUNICATIONS 84
CONTROL PREFIX 85
FORMAT PREFIX 85
DELIMITER CHAR 85
ZPL MODE 86
MEDIA POWER UP 86
HEAD CLOSE 86
BACKFEED 87
LABEL TOP 87
LEFT POSITION 87
RTC TIME 89
PASSWORD 89
LANGUAGE 89
ZebraNet 90
LCD Explanation 91
Routine Care and 93
Adjustments 93
Cleaning Procedures 94
Clean the Sensors 97
Clean the Rewind Option 98
Clean the Peel-Off Assembly 99
Clean the Cutter Module 100
Lubrication 101
Fuse Replacement 101
Position the Label Sensor 102
Routine Care and Adjustments 103
Selecting Sensor on page 59 104
Troubleshooting 105
RIBBON OUT 106
RIBBON IN 106
PAPER OUT 106
HEAD OPEN 107
HEAD OVER TEMP 107
HEAD UNDER TEMP 107
CUTTER JAM 107
OUT OF MEMORY* 108
Print Quality Problems 109
Calibration Problems 110
Communication Problems 111
Miscellaneous 112
Printer Diagnostics 113
CANCEL Self Test 114
PAUSE Self Test 115
FEED Self Test 116
FEED and PAUSE Self Test 117
SAVE CHANGES 118
LOAD DEFAULTS 118
Data Connections 119
Serial Data Port 120
RS-232 Serial Data Port 121
(Printer) 122
(Modem, etc.) 122
Connector 124
Parallel Data Port 125
Specifications 127
General Specifications 128
Printing Specifications 129
Media Specifications 130
Ribbon Specifications 131
Printer Options 132
°, 90°, 180°, 270°) 133
Supported Bar Codes 134
Cutter Jam message, 89 136
Head Open message, 89 136
Head Over Temp message, 89 136
Head Under Temp message, 89 136
Out of Memory message, 90 137
Paper Out message, 88 137
Ribbon In message, 88 138
Ribbon Out message, 88 138
Customer Order # 13163LB 142

Commenti su questo manuale

Nessun commento

Zebra Z6Mplus Guida Utente Pagina 30

Commenti su questo manuale

Prodotti e manuali riguardandi Stampa e scansione Zebra Z6Mplus