Zebra RZ Series Guida Utente Pagina 108
- Pagina / 154
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Routine Maintenance
Routine Maintenance for the Rewind Option
108
79695L-003 Z Series
®
/RZ™ Series User Guide 1/11/11
Routine Maintenance for the Rewind Option
When you use the Rewind option, you will periodically need to remove printed labels or used
liner from the rewind spindle. You may also need to adjust the media alignment for the Rewind
option.
Remove Printed Labels or Liner from the Rewind Spindle
To remove printed labels or liner from the rewind spindle, complete these
steps:
1. Cut the liner between the media alignment spindle and the rewind spindle.
2. Rotate the take-up spindle counterclockwise until the rewind media guide is fully upright.
3. Loosen the thumbscrew on the rewind media guide.
- Z Series 1
- /RZ™ Series 1
- User Guide 1
- Part Number: 79695L-003 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Section Description 10
- T: Telephone 11
- F: Facsimile 11
- E: E-mail 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 18
- Control Panel 19
- Control Panel Buttons 20
- Control Panel Lights 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Temperature Relative Humidity 25
- Select a Site for the Printer 26
- I) may damage the 27
- Interface 29
- Standard or 29
- Optional 29
- Description 29
- O) position 32
- Power Cord Specifications 33
- Types of Media 34
- Ribbon Overview 36
- If the ribbon... Then 37
- Operations 39
- Print Mode Printer Option 41
- Load Media 43
- Roll Media 44
- Fanfold Media 44
- Roll Media (Continued) 45
- Fanfold Media (Continued) 45
- PAUSE to enable printing 47
- Close the printhead assembly 57
- Ribbon Coated Outside 58
- (black ribbon spindle) 58
- Ribbon Coated Inside 58
- (gray ribbon spindle) 58
- Load Ribbon 59
- Remove Used Ribbon 62
- Calibrate the Printer 63
- Media Width 64
- If the media... Then 65
- Adjust Printhead Pressure 66
- Configuration 67
- Setup Mode 68
- Exit Setup Mode 69
- Default Password Value 70
- SETUP/EXIT 71
- LIST SETUP 71
- PLUS (+) to confirm printing 71
- LIST NETWORK 72
- Language/Parameter 73
- To change the value shown: 73
- Action/Explanation 74
- WARNING REPLACE 80
- To format a memory card: 83
- To initialize Flash memory: 84
- To print a sensor profile: 84
- LOAD BACKING prompt displays 85
- RELOAD ALL displays 86
- To skip these parameters: 94
- IDLE DISPLAY 96
- Replacing Printer Components 100
- Lubrication 100
- Area Method Interval 101
- Routine Maintenance 102
- Cleaning Procedures 102
- Clean the Cutter Module 106
- I) the printer 107
- Troubleshooting 111
- Troubleshooting Checklists 112
- LCD Error Messages 113
- O) the printer 114
- HEAD COLD 115
- HEAD TOO HOT 115
- DEFRAGMENTING 116
- ERROR CONDITION 116
- CUTTER JAM 116
- OUT OF MEMORY 116
- (function) 116
- Print Quality Problems 117
- Note • A vertical drift of 119
- Calibration Problems 120
- NONE. See 121
- Ribbon Problems 122
- RFID Problems 123
- MEDIA POWER UP and 125
- LANGUAGE 126
- SAVE CHANGES in the 126
- O) and then on (I) 127
- CANCEL self tests 129
- CANCEL Self Test 130
- PAUSE Self Test 131
- FEED Self Test 132
- Print Quality Description 133
- FEED and PAUSE Self Test 135
- Printer Diagnostics 136
- RIBBON (2). If 137
- MEDIA (3) for the media 137
- Specifications 139
- General Specifications 140
- Printing Specifications 141
- Media Specifications 143
- Ribbon Specifications 144
- Printer Options 145
- 1/11/11 Z Series 147
- 79695L-003 Z Series 148
Prodotti e manuali riguardandi Stampa e scansione Zebra RZ Series
Stampa e scansione Zebra CPCL Specifiche
(70 pagine)
(70 pagine)
Stampa e scansione Zebra TTPM2 Specifiche
(140 pagine)
(140 pagine)
Stampa e scansione Zebra R2844-Z Manuale Utente
(86 pagine)
(86 pagine)
Stampa e scansione Zebra CPCL Specifiche
(497 pagine)
(497 pagine)
Stampa e scansione Zebra GK420t Guida Utente
(22 pagine)
(22 pagine)
Stampa e scansione Zebra 2746e Manuale Utente
(66 pagine)
(66 pagine)
Stampa e scansione Zebra MZ series Specifiche
(53 pagine)
(53 pagine)
Stampa e scansione Zebra 110Xi4 Manuale Utente
(22 pagine)
(22 pagine)
Stampa e scansione Zebra 2684 Manuale Utente
(70 pagine)
(70 pagine)
Stampa e scansione Zebra 400 Manuale Utente
(4 pagine)
(4 pagine)
Stampa e scansione Zebra ZXP Series 7 Manuale Utente
(134 pagine)
(134 pagine)
Stampa e scansione Zebra QLn420 Guida Utente
(103 pagine)
(103 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale