Zebra S-500 Guida Utente Pagina 41
- Pagina / 80
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Mechanical Adjustments
The Stripe printer has been designed with minimal operator adjustments required.
Print Quality Adjustments
In the factory, the Stripe printer is aligned and tested using Zebra’s 5319 ribbon and
Zebra’s Z-Trans 6A full width, non-continuous media to print thermal transfer labels at
Speed C (4"/sec). For other media/ribbon combinations, the user may need to adjust
Print Darkness, Toggle Pressure, or possibly the Printhead Position.
When changing from one media/ribbon combination to another, only slight changes in
Print Darkness or Toggle Pressure may be required. For these situations, refer to the
Toggle Pressure Adjustment on page 34. However, to achieve optimum print quality,
perform the adjustment procedure which follows. A #2 Phillips screwdriver and a
flathead screwdriver will be required.
I. Check the initial print quality.
1. Open the Media Compartment Door and Front Panel on the printer.
2. Load the recommended media and ribbon for your application and adjust
the Media Sensor Position.
3. Send a label format to the printer or activate the PAUSE Key Self Test (see
Chapter 4), print a few labels, and press the PAUSE key to stop printing.
4. Observe the print quality of the test labels. If it is satisfactory, complete the
process by turning the AC Power OFF. Otherwise, continue to Step II.
II. Adjust the print darkness.
1. Press the MODE key (DARKEN light and PAUSE light turn ON) to permit
darkness adjustment.
2. Press the PAUSE key to begin printing test labels.
3. While observing the print darkness, repeatedly press the UP (FEED) key to
make the printing DARKER, or the DOWN (CANCEL) key to make the
printing LIGHTER, until the desired darkness is achieved.
4. Once proper print darkness is achieved, press the PAUSE key to stop
printing.
If you are still experiencing poor print quality, perform the Toggle Pressure Adjustment
34. If that doesn’t correct your print problem, turn to the Appendix to adjust the
printhead position.
Note: Adjusting the position of the printhead should be done only after all of the above
attempts have been made to correct the situation.
3
Routine Care and Adjustment
33
- User’s Guide 1
- Warranty Information 3
- 1 Getting Started 9
- Site Requirements 10
- Printer Power Up 10
- Getting Started 10
- Communications 12
- Cutter Module Interface 12
- Media and Ribbon 13
- Adjusting the Media Sensor 18
- Ribbon Loading 19
- Ribbon Removal 20
- Initial Printer Test 21
- Configuration and Calibration 21
- 2 Operation 25
- Operator Controls 26
- Operation 26
- Operation 27
- Front Panel Lights 28
- Printer Status Sensors 29
- Sample ZPL II Label Formats 31
- 3 Routine Care and Adjustment 33
- Routine Care and Adjustment 34
- Lubrication 40
- AC Power Fuse Replacement 40
- Mechanical Adjustments 41
- Battery Replacement 44
- Troubleshooting Table 45
- Symptom Diagnosis Action 46
- Printer Diagnostics 49
- Extended Printer Diagnostics 52
- (Defaults) 56
- 6 Support Services 61
- Support Services 62
- Service Form 63
- Zebra Training Programs 67
- Appendix 71
- RS-232 Connector Pinout 73
- Data Signal Voltage Level 75
- HIGH = +5 VDC 75
- LOW = 0 VDC 75
- Glossary 77
Prodotti e manuali riguardandi Stampa e scansione Zebra S-500
Stampa e scansione Zebra 105Se Specifiche
(110 pagine)
(110 pagine)
Stampa e scansione Zebra G-SERIES Guida Utente
(58 pagine)
(58 pagine)
Stampa e scansione Zebra RZ Series Guida Utente
(154 pagine)
(154 pagine)
Stampa e scansione Zebra CPCL Specifiche
(70 pagine)
(70 pagine)
Stampa e scansione Zebra TTPM2 Specifiche
(140 pagine)
(140 pagine)
Stampa e scansione Zebra R2844-Z Manuale Utente
(86 pagine)
(86 pagine)
Stampa e scansione Zebra CPCL Specifiche
(497 pagine)
(497 pagine)
Stampa e scansione Zebra GK420t Guida Utente
(22 pagine)
(22 pagine)
Stampa e scansione Zebra 2746e Manuale Utente
(66 pagine)
(66 pagine)
Stampa e scansione Zebra MZ series Specifiche
(53 pagine)
(53 pagine)
Stampa e scansione Zebra 110Xi4 Manuale Utente
(22 pagine)
(22 pagine)
Stampa e scansione Zebra 2684 Manuale Utente
(70 pagine)
(70 pagine)
Stampa e scansione Zebra 400 Manuale Utente
(4 pagine)
(4 pagine)
Philips SHD9200/10 manuali
Manuali dei proprietari e guide per l'utente per Cuffie Philips SHD9200/10.
We fornisce 1 manuali pdf Philips SHD9200/10 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale